Price on the app only:
Special discount has ended
Please note each user for only 1 item(s)
if the goods arrival in 90 days,we will inform you by email!
Error appeared,Please try again later!
Questions & Answers
Your power goes to the center connections #3 & #4 your sensor goes to #5 & #6 the load (whatever your using it for) goes to #1 & #2. There is no polarity so it don't matter which way you hook it up. The only thing on you load hook up #1 & #2 you should run the hot wire side through them. Good Luck Max ( I see clchoice… see more Your power goes to the center connections #3 & #4 your sensor goes to #5 & #6 the load (whatever your using it for) goes to #1 & #2. There is no polarity so it don't matter which way you hook it up. The only thing on you load hook up #1 & #2 you should run the hot wire side through them. Good Luck Max ( I see clchoice gave you the same lay out) see less
By max brenneman on April 30, 2018
Yes, I left it unplugged overnight and the settings remained.
By Tissman on March 20, 2018
This uses a NTC thermistor (measuring resistance) and is not compatible with a thermocouple (measuring voltage).
By Chris Walker on April 28, 2018
It would depend on your refrigerator. Most refrigerators are cooled from a single compressor and coil system. Some have one compressor and two coils. You would need at least this dual-coil setup. The wiring hack would be very tricky and discouraged for a DIYer. These kinds of fridges are already expensive and messing … see more It would depend on your refrigerator. Most refrigerators are cooled from a single compressor and coil system. Some have one compressor and two coils. You would need at least this dual-coil setup. The wiring hack would be very tricky and discouraged for a DIYer. These kinds of fridges are already expensive and messing with the wiring would void the warranty and possibly destroy the machine. Probably easier and safer to get a dedicated fridge and freezer for each purpose you need. They come in all shapes and sizes, so space really wouldn't be a problem. see less
By DIY Hero on July 16, 2017
Temperature range for activating controller. Default is 2 deg F and it can be set between 1 and 30 deg F. It is meant to prevent over-cycling.
By Kman on April 19, 2018
The sensor appears potted quite well. For severe duty it may be placed in a well.
By Ed Lenk on February 15, 2018
They are for mounting into a rack.
By L. Tate on October 18, 2017
I'm using mine to control a 125 watt heat lamp so I would say yes, a 20watt heat strip would be well within the rated specs.
By usmillers on May 2, 2018
You are probably looking for a analog temperature controller for your system. This controler does on /off only and has a control band of a couple degrees. Not suitable for your application
By Bob on April 14, 2018
The probe is potted, but I don't think it looks like a probe designed for submersion. It is however a standard 10kohm NTC element which can be easily replaced with a waterproof version. I added extension wires to my probes to increase the measuring distance beyond 1 meter. There is also a calibration adjustment if necessary.
By J. Stuart on April 11, 2018
Please note that TOMTOP Forums are a community for all communicating and getting help each other. There will be some enthusiastic friends participate in your discussions. Of course TOMTOP customer service (with tomtop customer service icon) response is guaranteed ,which is the same way you contact us at http://drspanesallergist.com/contactsopen this forum in full page
based on 247 Customer Reviews
Share your thoughts with other customers and get Tomtop Points, the first 5 reviews get DOUBLE Tomtop Points!Write a Customer Review
November 6, 2015
November 5, 2015
March 16, 2018
March 5, 2018
March 1, 2018
January 16, 2018
By New Quilter
December 21, 2017
I bought this for a chest freezer to fridge modification which did an amazing job of dropping the power consumption for a solar application. I was impressed enough that I actually bought another as a backup. The instructions suck and actually say not to install "in the place where is dripping water, or the elderly, children could be touched" which can be interpreted many ways. The laughing from reading the instructions however inspired me to do some Google searching and the info I needed came up fairly quickly. Programming took a little effort but was easy after, remembers the setting if power is lost and the fact that it displays in F in a huge plus to me!
December 5, 2017
November 20, 2017
October 15, 2017
September 10, 2017
April 15, 2017
December 29, 2015
December 23, 2015
November 17, 2015
September 28, 2015
August 27, 2015
May 14, 2015
May 5, 2015
April 13, 2015
Top Sellers More
Your question has been submitted successfully
Please activate your account first. We will resend the activation email to help you complete your registration.
OUR SITE RUNS OF COOKIES